Ihr Warenkorb ist leer
Ihr Warenkorb ist leerDirekt nach der ersten Aushärtung kühlt die kryogene Behandlung den Stahl auf sehr niedrige Temperaturen ab, indem flüssiger Stickstoff auf bis zu -190 °C verwendet wird. Damit wird die Umwandlung von Austenit abgeschlossen, was sowohl die Härte als auch die Zähigkeit des Stahls erhöht. Benannt nach unserem Gründer Herrn Vaclav Richter, stellen diese Meißel die höchste Qualität unserer Herstellungsprozesse dar, die einzigartige Materialien, Wärmebehandlung und Bearbeitung kombinieren, um das beste Werkzeug für Holzarbeiter herzustellen. Jeder Meißel ist durch unser Markenzeichen Richter Extra gekennzeichnet.
Pierluigi Zoppelletto
Bewertet in Italien am 19. Mai 2024
Penso sia il miglior scalpello come rapporto qualità/prezzo: imbattibile per il prezzo rispetto ai più blasonati scalpelli d'oltre mare e per qualità perchè costruito con le migliori lame utilizzate nelle serie TOP di Narex, che di acciai non è seconda a nessuno.
Peter W.
Bewertet in Australien am 31. August 2023
So far I have only opened, sharpened and used the 19mm Narex Richter (I also bought a 3mm and 13mm).I used my diamond plate to flatten the back and found the back of the chisel is hollow. After about 5 minutes work, I had the area behind the edge flat across the width for about 10mm. This was annoying, as I expected better from Narex's premium bench chisel range.Then I put the chisel in my honing guide to sharepen the bevel. It was quickly apparent that the blade was not correctly ground, only one side of the bevel was being honed by the diamond plate. It took around 5 minutes again to get the bevel to be honed right across the width of theground bevel.I checked the edge of the chisel for squareness, and found that the bevel had been ground with a skew. This was fairly significant, and again very disappointing for Narex's premium bench chisel range.I completed honing to 1000 grit on my diamond plate and ended up with skewed, but sharp edge. The edge cut well on some mortises I was cleaning up in pine boards. It stayed sharp and pared the end grain and sides cleanly.These chisels aren't the most expensive, nor are they at the lower end of the price scale. I expected better shaping of the working part than I recieved. I will need to use my grinder to correct the skew, form a new bevel, then sharpen this one again from scratch. I'm hoping that the other two (3mm and 13mm), are better shaped out of the box.
Andrew Smith
Bewertet in Großbritannien am 9. Februar 2022
Very nice chisel easily sharpened up and seems to be holding edge very well.
polyspecific
Bewertet in den USA am4. September 2020
Buy it/them already, seriously. When I first grabbed the handle I just froze in amazement. I swear the handle was made for my hand, I just stared in complete wonder the first time I grabbed the handle. They were all ground as flat as any verified straight edge that I have, I couldn't find anything that was not flat. My one complaint is that I could not find a 12mm or 1/2" as a single blade...Go add to cart and checkout, you can read this afterward...Wood types make a difference so: I usually work with old growth, storm damaged, fallen trees in Southwest Virginia. I mill and air dry my wood.These were used on:Sugar Maple/Black mapleWalnut (english and black)Cherry.Exotics that I used these on are:BocoteBubingaPurple heartI rarely use a mallet, and keep my chisels as sharp.as possible so they push easier. If you use a mallet your results may differ.Did you already add to cart/checkout? If not, you should do that now.These are the best blades that I have. No hesitation saying that. I cannot say that these are the best you can get now, because my shop does not have the budget to compare these to the likes of Veritas and Lie Nielson. I have some Stanley sweetheart socket chisels, an Ashley Iles 12mm butt, a few regular narex, and a ragged selection of cheap beater chisels. I purchased the 3/4" because I do not like having to constantly stop to strop the stanley in mid project, now the stanley is generally unused. The Ashley Iles has good steel, but does not hold a candle to the edge retention on these. The Richter chisels hold their edge very very well.The shoulders/side bevels and overall geometry on these things is amazing. The Richter's have thinner side bevel than the Ashley Iles 1/2 butt chisel. It used to be my go-to for cleaning out dovetails, not anymore. The Richters will slip in tighter corners. I love these and if I see one in half inch I will be grabbing it asap. Checking for the 1/2" Richter is what brought me here today, then I realized that I had not written a review for these awesome chisels. They deserve a review.This will be posted 3 times... Once for each purchased product. Need to make sure it is seen if someone filters by size.
StealthLS2
Bewertet in den USA am23. September 2020
Don’t make the same mistake that I did. Within a minute of unwrapping this chisel I knew immediately I had made a grave error. I started the return process so that I could instead get the whole box set. These chisels are friggin beautiful. I’d been obsessing for the last couple weeks over which chisels to get, checking out local stores, watching videos and reading a gazillion reviews. I only needed a couple, bought the most used 1/2 and 3/4, but after holding the first I just had to have more. Although I did not take them to the sharpening plate a straight edge showed the back to be true flat. They seemed sharp out of the box, although I expect to tune them up in pursuit of perfection like I would with any good chisel. Unfortunately I can’t speak yet to how well they work, they’re already enroute back to the very cooperative and super fast shipping seller, but check on YouTube and see what some expert craftsman have to say about them. I think these are a tremendous value for a premium quality chisel. Go ahead and get one, you too will regret not getting more before the Richter run is all gone.
Produktempfehlungen
29.90€
15 .99 € 15.99€